泊头市 卓远机械设备制造有限公司

快速联系:卓远机械 卓远机械

产品目录

联系我们

公司名称:泊头市 卓远机械设备制造有限公司
注册地址:河北省 泊头市交河开发区
传真号码:0317-8031093
联系方式:15369812793 (微信同号)褚连胜
邮政编码:062151
企业邮箱: 1358827475@qq.com
账号开户银行:中国银行泊头支行
账号:100399943203
农行账号:6228481739059615270
Company name: botou zhuoyuan mechanical equipment manufacturing co.,LTD
Registered address: jiaohe development zone, botou city, hebei province
Fax number: 0317-8031093
Contact information: 15369812793 (WeChat with the same number)  liansheng chu
Postcode: 062151
Enterprise email:1358827475@qq.com
Account Opening Bank: Botou Branch of Bank of China
Account number: 100399943203
Agricultural bank account number: 6228481739059615270

最新动态

您的位置:卓远机械 >> 产品展示 >>铸铁平板平台系列

【】 150平大型装配平台[150 flat large assembly platform]

时间:2019-6-6 17:27:45 作者:网站管理员 点击:100316 次
150平大型装配平台[150 flat large assembly platform]

铸铁装配平板规格:1000×750-3000×6000(mm),特殊规 格可根据用户需求制造,大于此 规格的装配平台可以拼接。 Cast iron assembly plate specifications: 1000 *750-3000 *6000 (mm), special specifications can be manufactured according to user needs, larger than this specification assembly platform can be spliced.

本次平台为10块3米*5米的平台拼接而成。有需要 的朋友可以电话联系15369812793.

装配平 台又称装配平板,装配定盘,主要应 用于动力机械设备的装配及调试,表面带有T形槽,可以固 定动力机械设备,可以拼装使用。

技术要求:
1、装配平 台工作面不得有严重影响外观和使用性能的砂孔、气孔、裂纹、夹渣、缩松、划痕、碰伤、锈点等缺陷。
2、装配平 台的铸造表面应清除型砂且平整,涂漆牢固。
3、精度等记为0级-3级的平板工作面上,直径小于15mm的砂孔 允许用相同材料堵塞,其硬度 应小于周围材料的硬度。工作面 堵塞的砂孔应不多于4个,且砂孔 之间的间距应不小于80mm。
4、装配平 台应采用优质细密的灰口铸铁或合金等材料制造,其工作面硬度应为170-220HB。
5、装配平 台工作面通常应采用刮削工艺。对采用刮削加工的3级平板工作面,其表面粗糙度Ra的最大允许值为5um。
检验过程:

装配平台是划线、测量、铆焊、工装工 艺不可以缺少的工作台,也可以 做机械试验平台等等。在装配 平台的生产设计上采用箱体式、筋板式 或其他结构型式。在装配 平台的相对两侧面上,应有安 装手柄或吊装位置的设置、螺纹孔或圆柱孔。装配平 台经检定符合标准要求后,应附有产品合格证;产品合 格证上应有本标准的标准号和产品序号。
从装配 平台的整个检验过程中来看,平板本身为测量基面,其放置应稳定;用自准直仪检定时,仪器与 平板不在同一刚体上.仪器支 架牢固性尤为重要。所以装 配平台的检定规程要求检定场地应牢固稳定,检定地点应避免振动。这是因为:工厂常 将小平板置于钳工台或桌子上,牢固稳定性差。检定人 员在装配平台附近的走动、检定工 具在装配平台上的移动,都会产生不同的重力,使装配 平板的空间位置发生变化,测量结果不可靠。所以检定这类平板时,平板应 移至牢固稳定的场地上,避免重 力变化对测量结果的影响。

用途:应用于 动力机械设备的装配及调试,表面带有T形槽,可以固 定动力机械设备。工作面上可加工圆孔、U型孔或长孔。
精度:按国家 标准计量检定规程JJG117-91执行,分为3级、精刨两种。

铸铁装 配平台使用注意事项:
A使用之前,先进行安装调试,以防损 坏装配平台的工作面;
B使用过 程中要注意防潮、防腐蚀,同时注 意不要将装配平台放于过高和过低的温度环境下存放;
C工件的 重量不要超过铸铁装配平台的额定载荷,以免造 成工作质量降低以及损坏装配平板的结构使之变形。
D在铸铁 装配平台使用完毕后,应将其清洗干净,同时作好防锈工作。
一般铸 铁装配平台的使用寿命很长,只要采 用正确的方法使用和存放,装配平 台工作面的精度可以保持使用2年以上,当精度 降低时可以通过调试或刮研工艺恢复。

This platform is composed of 10 platforms of 3 meters * 5 meters. Friends in need can call 15369812793.

The assembly platform, also known as the assembly plate, is mainly used for the assembly and debugging of power mechanical equipment. With t-shaped groove on the surface, it can fix power mechanical equipment and can be assembled for use.

The technical requirements:

1. There shall be no defects such as sand holes, air holes, cracks, slag inclusion, shrinkage, scratches, bruises and rust spots which seriously affect the appearance and performance of the working face of the assembly platform.

2. The casting surface of the assembly platform should be clean and smooth, and the paint should be firm.

3. Accuracy is grade 0-3 on the flat surface. Sand holes less than 15 mm in diameter are allowed to be blocked by the same material, and their hardness should be less than that of surrounding materials. There should be no more than four sand holes blocked in the working face, and the spacing between the sand holes should be no less than 80 mm.

4. The assembly platform shall be made of fine gray cast iron or alloy with a hardness of 170-220HB.

5. Scraping technology is usually used in the working face of assembly platform. The maximum allowable value of surface roughness Ra is 5um for the three-stage plate working face which is machined by scraping.

The inspection process:

The assembly platform is a workbench that can not be lacking in scribing, measuring, riveting, and tooling processes, and can also be used as a mechanical test platform. Box-type, ribbed or other structural types are used in the production design of the assembly platform. On the opposite sides of the assembly platform, there should be a mounting handle or a lifting position, a threaded hole or a cylindrical hole. After the assembly platform has been verified to meet the standard requirements, it shall be accompanied by a product certificate; the product certificate shall have the standard number and product serial number of this standard.

From the whole inspection process of the assembly platform, the flat plate itself is the measuring base surface, and its placement should be stable. When calibrating with the autocollimator, the instrument and the flat plate are not on the same rigid body. The stability of the instrument support is particularly important. Therefore, the verification rules of assembly platform require that the verification site should be firm and stable, and the verification site should avoid vibration. This is because: factories often place small plates on benches or tables, the firm stability is poor. The movement of calibration personnel near the assembly platform and the movement of calibration tools on the assembly platform will generate different gravity, which will change the space position of the assembly plate, and the measurement results are unreliable. Therefore, when calibrating this kind of plate, the plate should be moved to a firm and stable site to avoid the influence of gravity change on the measurement results.

Usage: It is used for assembling and debugging of power machinery equipment, with T-groove on the surface, and can fix power machinery equipment. Round, U-shaped or long holes can be machined on the working face.

Accuracy: According to the national standard verification regulation JJG117-91, it can be divided into three levels and fine planing.

Precautions for use of cast iron assembly platform:

A. Installation and debugging should be carried out before use to prevent damage to the working surface of the assembly platform;

B. Pay attention to moisture and corrosion prevention during use, and do not store the assembly platform at too high or too low temperature;

C. The weight of the workpiece should not exceed the rated load of the cast iron assembly platform, so as not to reduce the working quality and damage the structure of the assembly plate to make it deformed.

D. After the use of the cast iron assembly platform, it shall be cleaned and rust prevention shall be done at the same time.

Generally, the service life of cast iron assembly platform is very long. As long as the correct method is used and stored, the accuracy of the working face of the assembly platform can be maintained for more than 2 years. When the accuracy is reduced, it can be restored by debugging or scraping.

Company name: botou zhuoyuan mechanical equipment manufacturing co., LTD

Registered address: jiaohe development zone, botou city, hebei province

Fax number: 0317-8031093

Contact information: 15369812793 (WeChat with the same number)  liansheng chu

Postcode: 062151

Enterprise email:1358827475@qq.com

Account Opening Bank: Botou Branch of Bank of China

Account number: 100399943203

Agricultural bank account number: 6228481739059615270

  • 售前咨询
友情链接:    拉手彩票   大发彩票备用网站   天荣棋牌登陆   金得胜棋牌唯一官方网站   拉手彩票